Brunswick GS-X Series Скачать руководство пользователя страница 238

Страница: 238 / 302

6-14

Section 6: Troubleshooting

Section Rev. February 2009

PROBLEM

CAUSE

CORRECTIVE ACTION

Pinsetter does not turn on properly.

TS1 or TS2 safety switch actuated.

Photocell not adjusted properly.

Faulty switch "A" or "SM".

Nexgen Controller main switch is

off. The main power cable is

unplugged, the mechanic's rear

stop switch is not on.

Main house breaker box (if two

pinsetters are down.)

Incorrect line voltage.

Pinsetter set to wrong mode.

Determine cause of trouble, repair,

and restart machine.

Adjust ball detector.

Replace or adjust switch.

Turn on all switches. Check plugs

and connectors.

Reset breakers.

Have line voltage corrected.

Set machine to proper mode

Pinsetter cycles independently.

(One cycle only.)

CAUTION: Camera flash may

cause pinsetter to cycle

independantly.

Photocell not adjusted properly.

Loose reflector mounting.

Faulty power supply connections.

Nexgen mode setting is wrong.

Incoming 3 phase power surge, or

is out of balance

Check for proper hardware and

adjust.

Remount with proper hardware and

adjust.

Tighten connections.

Place pinsetter mode in 10-pin

mode (stand alone pinsetters) or in

(Frmwrx) mode if attached to the

Frameworx scorer.

As a last resort, consult a qualified

electrician to help identify the

surge and correct the problem.

Содержание GS-X Series















































































































































































































































































































Результаты поиска

Содержание GS-X Series

Отзывы:

Похожие инструкции для GS-X Series

Бренды по названию

Популярные бренды

Brunswick GS-X Series, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание GS-X Series

Отзывы:

Похожие инструкции для GS-X Series

Бренды по названию

Популярные бренды