Brunswick GS-X Series страница 113 Скачать руководство пользователя

Страница: 113 / 302

Section Rev. February 2017

Section 3: Nexgen Electronics

3-21

Enable 50 ERR (Y or N) -

This selection allows pinfall detection to be

monitored or ignored during machine cycle diagnostics.

Y -

Enable Codes (default)

N -

Disable Codes

Enable Foul: (Y or N) -

This selection allows you to accept or ignore the

foul signal coming from the foul unit.

Y -

The pinsetter will accept the foul signal (default)

N -

Foul Signals are ignored.

Dist Slow Start: (Y or N) -

The selection determines whether the

distributor will start slowly and gradually increase speed or start at full

speed. The suggested setting for this option is ”N”. This selection is

available on machines beginning with software version 4.08.02. It was

been removed for software versions 4.95.21 and later.

Y -

Slow start enabled

N -

Slow start is disabled (default)

Long Err Codes: (Y or N) -

This selection is available on machines with

software version 4.08.02 and higher. The selection determines whether

the display will show error code using the standard 2 digit code or

extended code.

Y -

Display error codes using extended format

N -

Display error codes using 2 digit format

Pinlight: (Y or N) -

This selection is available on machines with

version 4.08.02 and higher. This selection turns on the pinlight so that the

pins are illuminated even when the machine is unassigned.

Y -

Pinlight on

N -

Pinlight off (default)

Enable PF Err: (Y or N)

- This selection is available on machines with

software version 4.95.21 and higher. This selection allows the mechanic

to enable (or disable) an error code that would occur in the event that the

pinsetter loses power.

- Enable the code (default)

- Disable the code

Off Sweep Dwn: (Y or N)

- This selection is available on machines with

software version 4.95.21 and higher.This selection causes the sweep to

drop when the lane is turned off from the scorer. The sweep will not drop

when the pinsetter is turned off via a local mechanic’s switch.

- Enable sweep drop

- Disable sweep drop (default)

Содержание GS-X Series















































































































































































































































































































Результаты поиска

Содержание GS-X Series

Отзывы:

Похожие инструкции для GS-X Series

Бренды по названию

Популярные бренды

Brunswick GS-X Series, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание GS-X Series

Отзывы:

Похожие инструкции для GS-X Series

Бренды по названию

Популярные бренды