Brunswick GS-X Series страница 233 Скачать руководство пользователя

Страница: 233 / 302

Section Rev. February 2009

Section 6: Troubleshooting

6-9

CODE EXTENDED

CODE*

FAILURE DESCRIPTION

POSSIBLE CAUSES

Detect10

Detect1

Detect2

Detect3

Detect4

Detect5

Detect6

Detect7

Detect8

Detect9

PIN NOT DETECTED IN DIAGNOSTICS -

These ten codes are

used during Machine Cycling

diagnostics only. If a standing pin is not

detected when the pinsetter is

operating in this mode, the pinsetter will

stop and display the code for the pin

not detected. To activate this option set

the Enable 50 Err setup option to "Y"

Check the pin detector plate for proper positioning. Is it level from left to right.

Check the Stroke Limiter height adjustment.

Check the setting table levelness.

Check the angle "1" and "2" adjustment.(Pinsetter Timing)

Check stroke limiter shock.

A Found

SWITCH A NOT EXPECTED BUT

FOUND - Pinsetter CPU has requested

that the table be lowered but the "A"

switch is still being held closed.

Table Motor or brake defective preventing table from being lowered.

The wiring between the switch and P-1/P-23 on the Nexgen Controller is

defective.

Bad Connection on the H.V. PCB or Bad H.V. PCB (Nexgen)

Faulty A-Switch

B Found

SWITCH B NOT EXPECTED BUT

FOUND - This switch was actuated at the

wrong time or continuously.

Switch "B" on the switch cluster is shorted. Check the wiring and the switch.

Table motor or brake defective

C Found

SWITCH C NOT EXPECTED BUT

FOUND - This switch was actuated at the

wrong time or continuously.

Switch "C" on the switch cluster is shorted. Check the wiring and the switch.

Nexgen CPU defective. Check the wiring and swap the PCBs with a working

lane pair.

Table motor or brake defective.

D Found

SWITCH D NOT EXPECTED BUT

FOUND - This switch was actuated at the

wrong time or continuously.

Switch "D" on the switch cluster is shorted. Check the

wiring and the switch.

Table motor or brake defective

Nexgen CPU defective. Check the wiring and swap the PCBs with a working

lane pair.

SMFound

SWITCH SM NOT EXPECTED BUT

FOUND - This sweep motor switch is

actuated when it should not have been.

Sweep motor defective.

Sweep motor brake defective or stuck on the motor shaft.

No power to the sweep motor and/or brake. Check wiring

for damage and proper hookup.

"SM" switch shorted. Wiring between the Nexgen Controller and the switch is

shorted.

Sweep wagon or sweep arms binding or roller out of adjustment.

Содержание GS-X Series















































































































































































































































































































Результаты поиска

Содержание GS-X Series

Отзывы:

Похожие инструкции для GS-X Series

Бренды по названию

Популярные бренды

Brunswick GS-X Series, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание GS-X Series

Отзывы:

Похожие инструкции для GS-X Series

Бренды по названию

Популярные бренды