Brunswick GS-X Series Скачать руководство пользователя страница 243

Страница: 243 / 302

Section Rev. February 2009

Section 6: Troubleshooting

6-19

PROBLEM

CAUSE

CORRECTIVE ACTION

21.

Table does not set pins after

second ball or table is not full.

Pin jam in distributor.

Bent pin distributor guide tabs.

Faulty pin holder solenoid.

Table not adjusted to proper height.

Broken pin station on distributor.

Not enough pins in machine.

Broken pin holder electrical

connections.

Faulty electronics.

Faulty pin holder switch or switch

actuator.

Remove jam.

Adjust as required.

Replace solenoid as required.

Adjust table.

Replace as required.

Be certain 22 pins are in machine.

Repair connections.

Change the Nexgen CPU PCB.

Repair pin holder switch or switch

actuator.

22.

Table is full but does not lower.

Faulty pinholder microswitches.

CPU fuse Is blown (Nexgen).

Faulty Nexgen CPU or H.V. PCB .

Pin holder switch actuator sticking.

Pin detector plate stuck up.

Pin holder out of postion detector

plate hangs up.

Adjust or replace microswitches.

Replace fuse

Replace faulty box or PCB.

Repair

Check clearance between plate

and pin holders.

Adjust pin holder assembly.

23.

Pins wobble or fall over while being

set.

Pin holders not plumb.

Table not adjusted for proper

height.

Table is not completely level.

Faulty table spring.

Pin bottoms are worn.

Make sure pin holders are vertical.

Adjust table height.

Level table.

Replace spring.

Scrap or repair worn pins.

Содержание GS-X Series















































































































































































































































































































Результаты поиска

Содержание GS-X Series

Отзывы:

Brunswick GS-X Series, Руководство по эксплуатации и обслуживанию, Страница: 243 / 302

Результаты поиска

Содержание GS-X Series

Отзывы: