APRILIA TUAREG 660 Скачать руководство пользователя

Страница: 154 / 311

•

Working both on the upper and lower

part of the steering headstock, insert

the rotation seats of the bearings (4) up

to the stop using the appropriate

punch.

•

Lubricate the inserted seats with

grease.

•

Insert the complete triple clamp (5) into

the headstock.

•

Supporting the lower triple clamp, in-

sert the inner ring of the bearing (6)

complete with balls on the headstock

and lubricate it.

•

Supporting the lower triple clamp, lu-

bricate the upper seat (7) of the bearing

and insert it on the headstock.

Suspensions

TUAREG 660

SUSP - 154

Содержание TUAREG 660
























































































































































































































































































































Результаты поиска

Содержание TUAREG 660

Отзывы:

Похожие инструкции для TUAREG 660

Бренды по названию

Популярные бренды

APRILIA TUAREG 660, Руководство по обслуживанию станции

Результаты поиска

Содержание TUAREG 660

Отзывы:

Похожие инструкции для TUAREG 660

Бренды по названию

Популярные бренды