APRILIA TUAREG 660 Скачать руководство пользователя страница 256

Страница: 256 / 311

Removal

To remove the front brake master cylinder it is

necessary to previously drain the front system, re-

move the rear view mirror and handguard com-

plete with support. Then proceed as described:

•

Remove the rubber grommets that fas-

ten the brake line to the wiring harness.

•

Unscrew the fixing screw of the brake

line complete with the two washers.

•

Unscrew the two fixing screws of the U-

bolt to completely remove the brake

master cylinder.

Installing

To install the front master cylinder, carry out the procedures described above in reverse order. Then fill

the system and bleed it.

PAY ATTENTION TO USE NEW WASHERS TO FASTEN THE SCREW OF THE BRAKE LINE.

Rear brake pump

Braking system

TUAREG 660

BRAK SYS - 256

Содержание TUAREG 660
























































































































































































































































































































Результаты поиска

Содержание TUAREG 660

Отзывы:

Бренды по названию

Популярные бренды

APRILIA TUAREG 660, Руководство по обслуживанию станции

Результаты поиска

Содержание TUAREG 660

Отзывы:

Бренды по названию

Популярные бренды