APRILIA TUAREG 660 Скачать руководство пользователя

Страница: 168 / 311

REMOVAL OF EXTERNAL WHEEL COMPO-

NENTS

To proceed with the removal of the external wheel

components, proceed as described:

•

Remove the six fixing screws (9) of the

tone wheel / front disc.

•

Remove the tone wheel (10) (if

present).

•

Remove the brake disc (11).

Checking

FRONT WHEEL BEARINGS

Check the bearings installed on the wheel.

CHECK THE CONDITION OF ALL COMPONENTS AND OF THE COMPONENTS INDICATED AS
FOLLOWS IN PARTICULAR.

CHECKING ROTATION

•

Manually rotate the inner race of each bearing. The race must turn smoothly without im-

pediment or noise.

If one or both bearings do not fall within the control parameters:

•

Replace both wheel bearings.

CHECKING RADIAL AND AXIAL PLAY

Chassis

TUAREG 660

CHAS - 168

Содержание TUAREG 660
























































































































































































































































































































Результаты поиска

Содержание TUAREG 660

Отзывы:

Похожие инструкции для TUAREG 660

Бренды по названию

Популярные бренды

APRILIA TUAREG 660, Руководство по обслуживанию станции

Результаты поиска

Содержание TUAREG 660

Отзывы:

Похожие инструкции для TUAREG 660

Бренды по названию

Популярные бренды