APRILIA TUAREG 660 Скачать руководство пользователя

Страница: 153 / 311

•

Remove the lower seat of the bearing

(10) using a standard bearing extractor

To remove the lower steering bearing:

•

After removing the inner bearing ring

(11) complete with balls from the head-

stock tube, heat the lower bearing seat

(12) with a hot air gun to remove it and

then slide off the dust cover (13).

•

Remove the upper seat of the lower

bearing (14) from below using a stand-

ard bearing extractor.

DURING THE INSTALLATION OF THE BEARINGS, IT IS NECESSARY TO GREASE THEM BE-

FORE INSERTING THEM IN THE STEERING HEADSTOCK.

Assembling

To assemble the steering assembly, proceed as

described:

•

Place the dust cover (1) on the steering

headstock.

•

Insert the lower seat of the bearing (2)

and the inner ring of the bearing (3)

complete with balls, sprinkling them

with grease

TUAREG 660

Suspensions

SUSP - 153

Содержание TUAREG 660
























































































































































































































































































































Результаты поиска

Содержание TUAREG 660

Отзывы:

Похожие инструкции для TUAREG 660

Бренды по названию

Популярные бренды

APRILIA TUAREG 660, Руководство по обслуживанию станции

Результаты поиска

Содержание TUAREG 660

Отзывы:

Похожие инструкции для TUAREG 660

Бренды по названию

Популярные бренды