APRILIA TUAREG 660 Скачать руководство пользователя страница 12

Страница: 12 / 311

•

Insert the rear-view mirror complete

with protective rubber and lock nut on

the mount.

•

Adjust the angle of the rear view mirror

and tighten the lock nut.

WINDSCREEN INSTALLATION PROCEDURE

•

Remove the screws together with

bushes and grommets, paying atten-

tion to recover the bushes positioned

on the support.

•

Insert the rubber grommets on the

windscreen.

•

Position the windscreen on the sup-

port, insert the four screws complete

with bushings and, making sure that

the bushings are correctly inserted in

the support, tighten the windscreen

screws to a torque of 9 Nm (6.63 lbf ft).

Aesthetic inspection

- Paintwork

- Fitting of Plastic Parts

- Scratches

Pre-delivery

TUAREG 660

PRE DE - 12

Содержание TUAREG 660
























































































































































































































































































































Результаты поиска

Содержание TUAREG 660

Отзывы:

Бренды по названию

Популярные бренды

APRILIA TUAREG 660, Руководство по обслуживанию станции

Результаты поиска

Содержание TUAREG 660

Отзывы:

Бренды по названию

Популярные бренды