APRILIA TUAREG 660 Скачать руководство пользователя

Страница: 260 / 311

•

Unscrew the fixing screw (3) complete

with washer (4) of the rear brake sys-

tem cable guides, taking care to recov-

er the spacer (5).

THE MODULATOR-REAR BRAKE MASTER

CYLINDER BRAKE LINE (6) IS POSITIONED IN-

TERNALLY.

•

Unscrew the fixing screw (7) complete

with the two washers (8) and remove

the brake line (9).

MODULATOR - FRONT BRAKE MASTER CYL-

INDER BRAKE LINE

•

Unscrew the fixing screw (1) with the

two washers (2).

•

Unscrew the three screws (3) and re-

move the support plate (4) of the en-

gine to the frame to facilitate the

removal of the cable clamp under-

neath.

Braking system

TUAREG 660

BRAK SYS - 260

Содержание TUAREG 660
























































































































































































































































































































Результаты поиска

Содержание TUAREG 660

Отзывы:

Похожие инструкции для TUAREG 660

Бренды по названию

Популярные бренды

APRILIA TUAREG 660, Руководство по обслуживанию станции

Результаты поиска

Содержание TUAREG 660

Отзывы:

Похожие инструкции для TUAREG 660

Бренды по названию

Популярные бренды