APRILIA TUAREG 660 Скачать руководство пользователя

Страница: 116 / 311

ERROR RELATED TO THE BATTERY VOLTAGE

For vehicles provided with injection, it is recom-

mended to check if there are any errors related to

the battery voltage.

The errors can be detected during the "Actual"

state but, more likely, they will be in the "Memo-

rised" state and thus with the warning lamp off.

If the error is "Battery voltage higher than the

specified value", replace the voltage regulator.

If following the static checks no anomaly is detec-

ted, it is recommended to proceed with the dy-

namic checks.

PRELIMINARY CHECK OF THE RECHARGE SYSTEM

A summary check of the recharge performance

can be performed by connecting the multimeter

with voltmeter function to the battery poles.

Observe the battery voltage during standby and

then start the engine and progressively accelerate

until 3000 rpm.

If the recharge system is efficient, the battery volt-

age increases progressively until 13.5-14.5V.

Connect an induction ammeter clamp to the posi-

tive (or negative) cables at the regulator's output.

Prepare an additional load of 140W (e.g. 4 12V

35W bulbs in parallel).

Start the engine and then connect the additional

load to the battery.

Electrical system

TUAREG 660

ELE SYS - 116

Содержание TUAREG 660
























































































































































































































































































































Результаты поиска

Содержание TUAREG 660

Отзывы:

Похожие инструкции для TUAREG 660

Бренды по названию

Популярные бренды

APRILIA TUAREG 660, Руководство по обслуживанию станции

Результаты поиска

Содержание TUAREG 660

Отзывы:

Похожие инструкции для TUAREG 660

Бренды по названию

Популярные бренды