APRILIA TUAREG 660 Скачать руководство пользователя страница 162

Страница: 162 / 311

ALWAYS REPLACE THE OIL SEALS WITH NEW COMPONENTS AFTER DISASSEMBLING THE

COMPONENTS OF THE SINGLE LINKAGE

Installing

To install the linkages, after securing the front of

the vehicle with straps, use a scissor lift to support

the centre of the vehicle and keep the rear shock

absorber unloaded.

Then proceed as described:

DUAL LINKAGE

•

Insert the fixing screw of the dual link-

age to the swingarm from the right side

and the lock nut from the opposite side,

tightening it to the prescribed torque.

•

Insert the screw fastening the shock

absorber to the dual linkage and tight-

en it to the prescribed torque.

SINGLE LINKAGE

•

Insert the fixing screw of the single link-

age to the swingarm from the left side

and the lock nut from the opposite side,

tightening it to the prescribed torque.

Suspensions

TUAREG 660

SUSP - 162

Содержание TUAREG 660
























































































































































































































































































































Результаты поиска

Содержание TUAREG 660

Отзывы:

Бренды по названию

Популярные бренды

APRILIA TUAREG 660, Руководство по обслуживанию станции

Результаты поиска

Содержание TUAREG 660

Отзывы:

Бренды по названию

Популярные бренды