APRILIA TUAREG 660 Скачать руководство пользователя страница 54

Страница: 54 / 311

Adjusting the levers

FRONT BRAKE LEVER

It is possible to adjust the distance between the

end of the lever (1) and the grip (2), turning the

adjuster (3).

•

Push the control lever (1) forwards and

turn the adjuster (3) until the lever (1)

is at the desired distance.

•

Turning the adjuster anticlockwise, the

lever (1) gets closer to the grip (2).

REAR BRAKE LEVER

The control lever is set to the correct ergonomic

position during assembly of the vehicle.

To adjust the play of the lever:

•

Position the vehicle on its stand and

remove the right frame cover.

•

Unscrew the lock nut (4) partially.

•

Turn the pin (5) checking with a thick-

ness gauge the correct play in the in-

dicated point - 1.5 mm (0.05 in).

•

Finish the adjustment by tightening the

lock nut.

Regolazione leva frizione

Adjust the clutch lever if the engine stalls or if the

vehicle creeps forward when the lever is pulled, or

if the clutch slips, causing a lag in acceleration rel-

ative to increases in engine speed.

Minor adjustments can be realized by acting on the

clutch lever adjuster operating as follows:

•

Turn the adjuster (1) clockwise to in-

crease the play of the lever (2) and

check the operation of the lever sitting

on the vehicle and grasping the hand

grip (3) as when in the riding position.

Maintenance

TUAREG 660

MAIN - 54

Содержание TUAREG 660
























































































































































































































































































































Результаты поиска

Содержание TUAREG 660

Отзывы:

Бренды по названию

Популярные бренды

APRILIA TUAREG 660, Руководство по обслуживанию станции

Результаты поиска

Содержание TUAREG 660

Отзывы:

Бренды по названию

Популярные бренды