APRILIA TUAREG 660 Скачать руководство пользователя страница 191

Страница: 191 / 311

•

Remove the 4 gaskets (11).

•

Using a suitable punch, remove the

roller bearings.

Specific tooling

020376Y

Adaptor handle

020441Y

26 x 28 mm adaptor

•

To remove the chain guide, refer to the specific procedure in the "chain guide sliders" para-

graph, in the "frame and suspension" chapter.

See also

Chain sliders

Checking

CAUTION

CHECK THAT NO COMPONENT IS NOTICEABLY DISTORTED, DAMAGED, CRACKED AND/OR
DENTED.
REPLACE ALL DAMAGED COMPONENTS.

ROLLER CASINGS

Turn the roller casings manually; they must rotate smoothly, continuously and silently.

There must be no axial clearance.

Replace the roller casings that present these problems.

Apply grease on the rollers.

GASKETS

Check that the gaskets are in good conditions; replace them if they show signs of damage or excessive

wear.

TUAREG 660

Chassis

CHAS - 191

Содержание TUAREG 660
























































































































































































































































































































Результаты поиска

Содержание TUAREG 660

Отзывы:

Бренды по названию

Популярные бренды

APRILIA TUAREG 660, Руководство по обслуживанию станции

Результаты поиска

Содержание TUAREG 660

Отзывы:

Бренды по названию

Популярные бренды