APRILIA TUAREG 660 Скачать руководство пользователя

Страница: 146 / 311

•

Place the handlebar (7) on the lower U-

bolts.

•

Position the upper U-bolt (8) with the

four fixing screws (9).

•

Adjust the handlebar with the "0" refer-

ence mark aligned with the lower U-

bolt and tighten the screws (9) to

torque.

•

Working from both sides, secure the

electrical component wiring harnesses

of the handlebars to the steering triple

clamp with two clamps.

Steering bottom yoke

Removing

To remove the lower triple clamp it is necessary to

first remove the front wheel complete with mud-

guard, the upper triple clamp and the stanchions.

Then proceed as described:

•

Remove the steering safety plate (1).

•

Remove the upper steering ring nut (2)

using the special tool.

Specific tooling

AP8140190

Steering tightening tool

Suspensions

TUAREG 660

SUSP - 146

Содержание TUAREG 660
























































































































































































































































































































Результаты поиска

Содержание TUAREG 660

Отзывы:

Похожие инструкции для TUAREG 660

Бренды по названию

Популярные бренды

APRILIA TUAREG 660, Руководство по обслуживанию станции

Результаты поиска

Содержание TUAREG 660

Отзывы:

Похожие инструкции для TUAREG 660

Бренды по названию

Популярные бренды