APRILIA TUAREG 660 Скачать руководство пользователя страница 239

Страница: 239 / 311

Removal

NOTE

THE FOLLOWING OPERATIONS REFER TO A SINGLE BRAKE CALLIPER BUT ARE VALID FOR
BOTH.

To remove the front brake calliper, after having

adequately protected the rim to prevent it from

coming into contact with the brake fluid when re-

moving the front brake calliper, it is necessary to

drain the front brake system. Then proceed as de-

scribed:

•

Unscrew and remove the special

screw complete with washers fixing the

brake hose to the calliper.

CAUTION

ALWAYS USE NEW SEALING WASHERS DURING REAS-
SEMBLY.

•

Undo and remove the two screws fixing

the front brake calliper to the stanchion

of the fork.

•

Remove the brake calliper together

with the support.

TUAREG 660

Braking system

BRAK SYS - 239

Содержание TUAREG 660
























































































































































































































































































































Результаты поиска

Содержание TUAREG 660

Отзывы:

Бренды по названию

Популярные бренды

APRILIA TUAREG 660, Руководство по обслуживанию станции

Результаты поиска

Содержание TUAREG 660

Отзывы:

Бренды по названию

Популярные бренды