APRILIA TUAREG 660 Скачать руководство пользователя

Страница: 238 / 311

•

Suitably protect the swingarm to pre-

vent it from coming into contact with the

brake fluid when connecting the brake

line.

•

Insert the special screw complete with

new washers fixing the brake line and

tighten it to the prescribed torque.

•

Connect the ABS sensor wiring to the

two cable glands.

•

Insert the ABS sensor in its seat and

secure it by tightening the screw to the

prescribed torque.

•

Fill the rear brake system checking its

level and restore the correct position-

ing of the wiring harness near the

breather screw, blocking it with the pro-

tection cap as indicated.

•

After reassembling the rear wheel, check the distance between the tone wheel and the ABS

sensor.

Characteristic

Distance between tone wheel and the rear sensor

0.5 - 2.00 mm (0.020 - 0.079 in)

Braking system

TUAREG 660

BRAK SYS - 238

Содержание TUAREG 660
























































































































































































































































































































Результаты поиска

Содержание TUAREG 660

Отзывы:

Похожие инструкции для TUAREG 660

Бренды по названию

Популярные бренды

APRILIA TUAREG 660, Руководство по обслуживанию станции

Результаты поиска

Содержание TUAREG 660

Отзывы:

Похожие инструкции для TUAREG 660

Бренды по названию

Популярные бренды