APRILIA TUAREG 660 Скачать руководство пользователя

Страница: 231 / 311

In case of replacement of the ABS control unit, ensure that the new one has caps on all four hydraulic

connections and then proceed as follows:

•

After connecting the new ABS control unit hydraulically and electrically, it must be activated/

recognised.

•

Do a "KEY ON".

•

Check that the ABS warning light flashes rapidly.

•

Do a "KEY OFF" followed by a "KEY ON".

•

If activation has been successful, the warning light should come on and flash slowly.

•

In the event of a fault, with the diagnostic tool disconnected, the warning light should be

permanently lit.

•

Connect the diagnostic tool and check for errors.

ABS CONTROL UNIT CONNECTOR INSERTION PROCEDURE

•

The initial position of the connector coupling lever must be as indicated in the figures.

•

Place the connector on the opposite

side of the control unit and lower the

driving lever until the "click" that signals

the end of the stroke is heard.

TUAREG 660

Braking system

BRAK SYS - 231

Содержание TUAREG 660
























































































































































































































































































































Результаты поиска

Содержание TUAREG 660

Отзывы:

Похожие инструкции для TUAREG 660

Бренды по названию

Популярные бренды

APRILIA TUAREG 660, Руководство по обслуживанию станции

Результаты поиска

Содержание TUAREG 660

Отзывы:

Похожие инструкции для TUAREG 660

Бренды по названию

Популярные бренды