APRILIA TUAREG 660 Скачать руководство пользователя

Страница: 140 / 311

•

Insert the sleeve on the stanchion and

using the special tool complete with

striker fully insert the guide bush (5),

the ring (4) and the oil seal (3).

Specific tooling

AP8140189

Tool for mounting the oil seal for

holes with diam. 43 mm (1.69 in)

AP8140146

Weight

•

Position the safety seeger ring in its

seat (2).

•

Insert the dust guard (1) into its hous-

ing correctly.

Filling oil

NOTE

THE FOLLOWING OPERATIONS REFER TO A SINGLE STANCHION BUT APPLY TO BOTH.

•

Place the sleeve upright in a vice fitted

with protection shoes.

•

Compress the sleeve in the stanchion.

Place a support under the stanchion in

order to leave it compressed.

•

Remove the white spacer of the damp-

er rod and the locking nut of the fork

cap screwed on the damper rod itself.

•

Pour part of the fork oil into the sleeve.

Suspensions

TUAREG 660

SUSP - 140

Содержание TUAREG 660
























































































































































































































































































































Результаты поиска

Содержание TUAREG 660

Отзывы:

Похожие инструкции для TUAREG 660

Бренды по названию

Популярные бренды

APRILIA TUAREG 660, Руководство по обслуживанию станции

Результаты поиска

Содержание TUAREG 660

Отзывы:

Похожие инструкции для TUAREG 660

Бренды по названию

Популярные бренды