APRILIA TUAREG 660 Скачать руководство пользователя

Страница: 142 / 311

•

After having screwed the specific tool

on the damper rod, insert the spring

(13) paying attention to the correct

alignment. The end where the spirals

are more compressed should be facing

upwards.

Specific tooling

AP8140150

Bored shaft for bleeding plunger

air

•

Position the pre-load tube (14) on the

spring, making sure that it is aligned

correctly. The narrower part must be

inserted into the spring.

•

Position the upper plate (15) on the

pre-load tube.

•

Before positioning the cap, adjust the

hydraulic regulator screw so that the

internal distance is as close as possi-

ble to 13 mm (0.51 in).

•

Position the specific tool to compress

the spring and with the help of a sec-

ond operator, after compressing the

spring, manually screw the cap (16)

until in contact with the control rod.

Tighten the nut (17) on the damper rod

to fasten the cap.

Specific tooling

020888Y

Pre-load tube clamp

Suspensions

TUAREG 660

SUSP - 142

Содержание TUAREG 660
























































































































































































































































































































Результаты поиска

Содержание TUAREG 660

Отзывы:

Похожие инструкции для TUAREG 660

Бренды по названию

Популярные бренды

APRILIA TUAREG 660, Руководство по обслуживанию станции

Результаты поиска

Содержание TUAREG 660

Отзывы:

Похожие инструкции для TUAREG 660

Бренды по названию

Популярные бренды