manualshive.com logo in svg

APRILIA TUAREG 660, Руководство по обслуживанию станции

Поделиться
Скачать
APRILIA TUAREG 660 Скачать руководство пользователя страница 203

Adjusting

To check the clearance:

•

Shut off the engine.

•

Rest the vehicle on the side stand.

•

Select neutral.

•

Check that the vertical deflection of the

bottom section of the chain, measured

at a distance of 320 mm (12.59 in) from

the centre of the rear wheel axle (along

imaginary line between centres of front

and rear sprockets), is approximately

48 mm (1.88 in).

•

Move the vehicle forwards to check the vertical deflection of the chain in other positions; the

chain deflection must be constant throughout the entire rotation of the wheel.

if the clearance is uniform, but greater or less than 

48 mm (1.88 in)

, carry out the adjustment.

CAUTION

IF THE CLEARANCE IS GREATER IN SOME POSITIONS IT MEANS THAT SOME ELEMENTS OF
THE CHAIN ARE CRUSHED OR HAVE SEIZED UP. IN THIS CASE THE CHAIN SHOULD BE RE-
PLACED.
LUBRICATE THE CHAIN REGULARLY TO PREVENT THE RISK OF SEIZURE.

For the adjustment of the chain tension:

•

Place the vehicle on its rear service

stand.

•

After completely loosening the nut (1),

operating from both sides, loosen the

two locknuts (2).

TUAREG 660

Chassis

CHAS - 203

Содержание TUAREG 660
























































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды