APRILIA TUAREG 660 Скачать руководство пользователя

Страница: 282 / 311

Instrument panel

To remove the instrument panel the top fairing

must be removed beforehand. Then proceed as

described:

•

Unscrew the four fixing screws (1) of

the instrument panel visor (2) and re-

move it

•

Unscrew the three screws (3) complete

with washers (4) securing the instru-

ment panel.

•

Disconnect the connector (5) of the in-

strument panel (6) and remove it.

Headlight assy.

To remove the front light cluster, first remove the

tank cover, the air ducts, the top fairing and the

instrument panel visor. Then proceed as descri-

bed:

•

Working on both sides of the vehicle,

remove the fixing screws (1) of then

headlight to the instrument panel sup-

port.

Bodywork

TUAREG 660

BODYW - 282

Содержание TUAREG 660
























































































































































































































































































































Результаты поиска

Содержание TUAREG 660

Отзывы:

Похожие инструкции для TUAREG 660

Бренды по названию

Популярные бренды

APRILIA TUAREG 660, Руководство по обслуживанию станции

Результаты поиска

Содержание TUAREG 660

Отзывы:

Похожие инструкции для TUAREG 660

Бренды по названию

Популярные бренды