APRILIA TUAREG 660 Скачать руководство пользователя

Страница: 305 / 311

•

Unscrew the two fixing screws (9) of

the left instrument panel support, tak-

ing care to recover the "T" bushes.

•

Remove the left instrument panel support.

•

To reassemble the instrument panel support, carry out the procedures described above in

reverse order, consulting the "electrical system" chapter to correctly position the wiring har-

nesses.

CENTRAL INSTRUMENT PANEL SUPPORT

It is possible to remove the central instrument pan-

el support without having to remove the side sup-

ports. To carry out this operation, proceed as

described:

•

Remove the windscreen, instrument

panel and instrument panel visor to dis-

connect the connectors attached to the

central instrument panel support.

•

Unscrew the four fixing screws and re-

move the central instrument panel sup-

port.

•

Disconnect the connectors connected

to the central instrument panel support.

TUAREG 660

Bodywork

BODYW - 305

Содержание TUAREG 660
























































































































































































































































































































Результаты поиска

Содержание TUAREG 660

Отзывы:

Похожие инструкции для TUAREG 660

Бренды по названию

Популярные бренды

APRILIA TUAREG 660, Руководство по обслуживанию станции

Результаты поиска

Содержание TUAREG 660

Отзывы:

Похожие инструкции для TUAREG 660

Бренды по названию

Популярные бренды