APRILIA TUAREG 660 Скачать руководство пользователя страница 83

Страница: 83 / 311

TABLE K2 - ENGINE HEAD AREA CONNEC-

TIONS

•

Connect the purge valve connector.

TABLE L - PROCEDURE FOR THE CORRECT FITTING OF THE ABS CONTROL UNIT CONNEC-

TOR

•

The initial position of the connector coupling lever must be as indicated in the figures.

TABLE L1 - PROCEDURE FOR THE CORRECT

FITTING OF THE ABS CONTROL UNIT CON-

NECTOR

•

Place the connector on the opposite

side of the control unit and lower the

driving lever until the "click" that signals

the end of the stroke is heard.

TUAREG 660

Electrical system

ELE SYS - 83

Содержание TUAREG 660
























































































































































































































































































































Результаты поиска

Содержание TUAREG 660

Отзывы:

Бренды по названию

Популярные бренды

APRILIA TUAREG 660, Руководство по обслуживанию станции

Результаты поиска

Содержание TUAREG 660

Отзывы:

Бренды по названию

Популярные бренды