APRILIA TUAREG 660 Скачать руководство пользователя

Страница: 56 / 311

To carry out vertical adjustment of the light

beam:

(LOW BEAM HEADLIGHTS)

•

Operating from the rear side of the fair-

ing, under the internal bodywork, act

on the adjuster ("1" left side / "2" right

side). SCREWING (clockwise) the light

beam is lowers; UNDO the screw (an-

ticlockwise) to raise the light beam.

•

These two adjuster screws may be

used to adjust the vertical alignment of

the low beam headlight beam.

NOTE

CHECK THAT THE VERTICAL ALIGNMENT OF THE BEAM
IS CORRECT.

(HIGH BEAM HEADLIGHT)

From under the light using a Phillips-head screw-

driver, act on the adjuster (3) at the point indicated:

•

Turn the screwdriver clockwise to raise

the beam;

•

Turn the screwdriver anticlockwise to

lower the beam.

This adjuster screw may be used to adjust the ver-

tical alignment of the high beam headlight beam.

NOTE

CHECK THAT THE VERTICAL ALIGNMENT OF THE BEAM
IS CORRECT.

Maintenance

TUAREG 660

MAIN - 56

Содержание TUAREG 660
























































































































































































































































































































Результаты поиска

Содержание TUAREG 660

Отзывы:

Похожие инструкции для TUAREG 660

Бренды по названию

Популярные бренды

APRILIA TUAREG 660, Руководство по обслуживанию станции

Результаты поиска

Содержание TUAREG 660

Отзывы:

Похожие инструкции для TUAREG 660

Бренды по названию

Популярные бренды