APRILIA TUAREG 660 Скачать руководство пользователя

Страница: 281 / 311

•

Disconnect the first connector of the

left switch cluster (6) from the guide on

the instrument panel support and dis-

connect it

•

Disconnect the second connector of

the left switch cluster (7).

•

Unscrew the fixing screw (8) of the right

switch cluster and slide it off the han-

dlebar to remove it.

USE NEW CLAMPS DURING REASSEMBLY.

Driving mirrors

Removing the rear-view mirrors:

•

Rest the vehicle on its stand.

•

Lift the rubber protection (1).

•

Loosen the fastening nut (2) by ensur-

ing that the threaded clamp (3) cannot

rotate.

•

Slide up and remove the complete

rear-view mirror unit (4).

Repeat the procedure to remove the other rear-

view mirror, if necessary.

UPON REFITTING AND BEFORE TIGHTENING THE LOCK-
ING NUT, MAKE SURE THAT THE REAR VIEW MIRROR
SUPPORT STEM IS ALIGNED WITH THE HANDLEBAR.

CAUTION

THE VEHICLE MAY NOT BE RIDDEN ON PUBLIC ROADS
WITH THE REAR VIEW MIRRORS REMOVED.

TUAREG 660

Bodywork

BODYW - 281

Содержание TUAREG 660
























































































































































































































































































































Результаты поиска

Содержание TUAREG 660

Отзывы:

Похожие инструкции для TUAREG 660

Бренды по названию

Популярные бренды

APRILIA TUAREG 660, Руководство по обслуживанию станции

Результаты поиска

Содержание TUAREG 660

Отзывы:

Похожие инструкции для TUAREG 660

Бренды по названию

Популярные бренды