manualshive.com logo in svg

APRILIA TUAREG 660, Руководство по обслуживанию станции

Поделиться
Скачать
APRILIA TUAREG 660 Скачать руководство пользователя страница 253

•

Remove the rubber protection cover of

the bleed valve.

•

Insert the transparent plastic pipe in

the front brake calliper bleed valve and

slide the other end of this pipe in a con-

tainer to collect the fluid.

•

Remove the front brake fluid reservoir

cap.

•

Quickly press and release the front

brake lever several times and then

keep it fully pressed.

•

Loosen the bleed valve by a 1/4 turn so

that the brake fluid flows into the con-

tainer, this will release the tension on

the brake lever and it which will make

it arrive at the end stop.

•

Close the bleed valve before arriving at

the end of the stroke with the lever.

•

Repeat the operation until the are no

air bubbles in the fluid going into the

container.

NOTE

WHILE PURGING THE HYDRAULIC SYSTEM, FILL THE
RESERVOIR WITH THE NECESSARY QUANTITY OF
BRAKE FLUID. CHECK THAT, DURING THE OPERATION,
THERE IS ALWAYS BRAKE FLUID IN THE RESERVOIR.

•

Screw the bleeding valve and remove

the pipe.

•

Top-up the reservoir until the correct

brake fluid level is obtained.

•

Refit and block the front brake oil res-

ervoir cap.

•

Refit the rubber protection cover.

BLEEDING SYSTEM WITH DIAGNOSTIC INSTRUMENT

If the brake lever still feels "spongy" after completing all checks, it is necessary to bleed the

brakes using this type of procedure.

•

With the diagnostic tool properly connected, select the function "FRONT BLEEDING" in the

section "SETTINGS".

TUAREG 660

Braking system

BRAK SYS - 253

Содержание TUAREG 660
























































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды