APRILIA TUAREG 660 Скачать руководство пользователя

Страница: 271 / 311

•

Remove the clamp (7), disconnect the

connector (8) of the right electric fan.

•

Remove the clamp (9), disconnect the

connector of the left electric fan.

•

Remove the radiator, sliding it out from

the left side of the vehicle.

Removing the expansion tank

To remove the expansion tank it is necessary to

remove the fuel tank, free the filter box without dis-

connecting it from the manifolds, remove the side

fairings and drain the system. Then proceed as

described:

•

Remove the metal clamps (1) and dis-

connect the hoses (2).

USE NEW METALLIC CLAMPS DURING IN-

STALLATION.

TUAREG 660

Cooling system

COOL SYS - 271

Содержание TUAREG 660
























































































































































































































































































































Результаты поиска

Содержание TUAREG 660

Отзывы:

Похожие инструкции для TUAREG 660

Бренды по названию

Популярные бренды

APRILIA TUAREG 660, Руководство по обслуживанию станции

Результаты поиска

Содержание TUAREG 660

Отзывы:

Похожие инструкции для TUAREG 660

Бренды по названию

Популярные бренды