APRILIA TUAREG 660 Скачать руководство пользователя страница 134

Страница: 134 / 311

Removing the fork legs

To remove the stanchions it is necessary to re-

move the sump guard, lift the front wheel using a

scissor lift, disconnect the front brake callipers, re-

move the wheel and the mudguard. Then proceed

as described:

THE FOLLOWING OPERATIONS REFER TO A

STANCHION BUT APPLY TO BOTH.

(IF APPLICABLE)

•

Unscrew the fixing screw of the ABS

wiring harness plate and remove it.

•

Undo the fixing screw of the ABS sen-

sor and remove it.

•

Unscrew the two locking screws of the

stanchion on the lower triple tree

clamp.

•

Unscrew the two locking screws of the

stanchion on the upper triple tree

clamp.

Suspensions

TUAREG 660

SUSP - 134

Содержание TUAREG 660
























































































































































































































































































































Результаты поиска

Содержание TUAREG 660

Отзывы:

Бренды по названию

Популярные бренды

APRILIA TUAREG 660, Руководство по обслуживанию станции

Результаты поиска

Содержание TUAREG 660

Отзывы:

Бренды по названию

Популярные бренды