Analog Devices SHARC ADSP-214 Series Скачать руководство пользователя | Manualshive

Страница: 730 / 1192

background image

Interrupts

20-16

ADSP-214xx SHARC Processor Hardware Reference

Listing 20-1. Enabling DPI UART Interrupts

bit set mode1 IRPTEN;    /* enables global interrupts */
bit set imask P1I;       /* unmasks P1I interrupt */
ustat1=dm(PICR0);               /* route UART0_RXI 0x13 to P1I */
bit set ustat1 P1I4|P1I1|P1I0;
bit clr ustat1 P1I3|P1I2;

dm(PICR0)=ustat1;

UART

The UART receive and transmit interrupts can also be programmed
through the peripheral interrupt control registers (

PICRx

) as separate inter-

rupts. (By default, these interrupts are not configured in the

IRPTL

register—the

PICRx

register has to be programmed to configure them.)

This method shown in

PICR

register with the code

value of the

UART_RXI

or

UART_TXI

interrupts.

Listing 20-2. Enabling UART Interrupts

bit set mode1 IRPTEN;      /* enables global interrupts */
bit set imask P1I;         /* unmasks P1I interrupt */
ustat1=dm(PICR0);          /* route UART0_RXI 0x13 to P1I */
bit set ustat1 P1I4|P1I1|P1I0;
bit clr ustat1 P1I3|P1I2;

dm(PICR0)=ustat1;

The following sections provide information on all of the available inter-
rupt sources.

DMA Interrupts

With system DMA enabled, the UART uses DMA to transfer data to or
from the processor. Dedicated DMA channels are available for receive and
transmit operations. Line error handling can be configured completely
independently from the receive/transmit setup.

www.BDTIC.com/ADI

«
...
728
729
730
731
732
...
»

Содержание SHARC ADSP-214 Series









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SHARC ADSP-214 Series

Univerge SV9300

Бренд: NEC Страницы: 26

Бренд: NEC Страницы: 20

DS2000 IntraMail

Бренд: NEC Страницы: 2

Бренд: Raritan Страницы: 4

Бренд: M86 Security Страницы: 46

HHM Series HHM2411

Бренд: TDK Страницы: 2

Бренд: ebm-papst Страницы: 11

DataPlot CB1224

Бренд: B-G Instruments Страницы: 4

Бренд: ZALMAN Страницы: 18

Developer's Board

Бренд: Sony Ericsson Страницы: 28

Бренд: McIntosh Страницы: 44

Бренд: Promise Technology Страницы: 148

Бренд: Me Страницы: 28

Бренд: Transition Networks Страницы: 5

Бренд: PACOM Страницы: 16

Бренд: Baicells Страницы: 38

Бренд: Zmotion Страницы: 57

BioSense Series

Бренд: ZKTeco Страницы: 96

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды