Analog Devices SHARC ADSP-214 Series Скачать руководство пользователя | Manualshive

Страница: 407 / 1192

background image

ADSP-214xx SHARC Processor Hardware Reference

8-11

Media Local Bus

The lower 14 bits (00 0001 0000 0000) and the 2 reserved bits “00” are
written in the

MLB_CNBCRx

register (write 0000 0100 0000 0000 = 0x0400

to bits 31–16 in the

MLB_CNBCRx

register for the start address or bits 15–0

for the end address). The remaining higher 5 bits (1 0000) are written in
one of the the base address registers, depending on the transfer mode. For
example, if using synchronous mode, write bits 31–16 = 0x0010 for
receive and bits 15–0 for transmit in the

MLB_SBCR

register.

The base address registers and offset registers use round robin arbitration
to determine which logical channel is granted access to the DMA bus.

more information, see “Programming Model” on page 8-16.

Ping-Pong DMA

Logical channels operate in ping-pong DMA mode when the channel
mode select bits (

MLB_CECRx

register bits 25–26) = 00. When MLB is con-

figured in ping-pong mode, the

MLB_CCBCRx

and

MLB_CNBCRx

registers are

used to configure and monitor the system memory current buffer and next
buffer respectively. Ping-pong DMA is available for all data types.

When receiving and transmitting asynchronous and control packet data,
the current buffer and next buffer are independent internal memory buf-
fers. This allows hardware to support the ping-pong buffering. Each buffer
is addressed using two 16-bit address fields in the

MLB_CNBCRx

and

MLB_CCBCRx

registers as described below.

• Next Buffer Start Address – CNBCRx.BSA – beginning of next

buffer in internal memory

• Next Buffer End Address – CNBCRx.BEA – ending of next buffer

in internal memory

• Buffer Current Address – CCBCRx.BCA – beginning of current

buffer in internal memory

• Buffer Final Address – CCBCRx.BFA – ending of current buffer in

internal memory

www.BDTIC.com/ADI

«
...
405
406
407
408
409
...
»

Содержание SHARC ADSP-214 Series









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SHARC ADSP-214 Series

Бренд: GE Страницы: 6

System x3630 M4

Бренд: IBM Страницы: 7

Бренд: Jetter Страницы: 35

PG-FLEX RT FRL-752

Бренд: PairGain Страницы: 6

Бренд: ZALMAN Страницы: 22

SmartMesh IA-510 D2511

Бренд: Dust Networks Страницы: 30

Бренд: Intel Страницы: 578

Бренд: 2N Telekomunikace Страницы: 67

Safeguard for Privileged Sessions 3000

Бренд: One Identity Страницы: 37

Бренд: Jäger Страницы: 54

Бренд: ICS Advent Страницы: 26

Бренд: UltrArmor Страницы: 3

Бренд: ubiquoss Страницы: 46

COM600 series 5.1

Бренд: ABB Страницы: 42

Бренд: StarTech.com Страницы: 2

Бренд: StarTech.com Страницы: 8

Бренд: A.E.B. Страницы: 12

NetLinx Master-Ethernet Card/Module NXC-ME260

Бренд: AMX Страницы: 162

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды