Analog Devices SHARC ADSP-214 Series Скачать руководство пользователя | Manualshive

Страница: 165 / 1192

background image

ADSP-214xx SHARC Processor Hardware Reference

3-35

External Port

Multibank Access

The processors are capable of supporting multibank operation, thus taking
advantage of the SDRAM architecture.



Operation using single versus multibank accesses depends only on
the address to be posted to the device, it is NOT an operation
mode.

Any first access to SDRAM bank (A) forces an activate command before a
read or write command. However, if any new access falls into the address
space of the other banks (B, C, or D) the SDC leaves bank (A) open and
activates any of the other banks (B, C, or D). Bank (A) to bank (B) active
time is controlled by t

RRD

= t

RCD

+ 1. This scenario is repeated until all

four banks (A–D) are opened and results in an effective page size of up to
four pages. This is because the absence of latency allows switching
between these open pages (as compared to one page in only one bank at a
time). Any access to any closed page in any opened bank (A–D) forces a
precharge command only to that bank. If, for example, two external port
DMA channels are pointing to the same internal SDRAM bank, this
always forces precharge and activation cycles to switch between the differ-
ent pages. However, if the two external port DMA channels are pointing
to different internal SDRAM banks, there is no additional overhead. See

Furthermore the SDC supports four external memory selects containing
each SDRAM. All external banks (

MS3-0

) provide multibank support, so

the maximum number of open pages is 4

×

4 = 16 pages.



Multibank access reduces precharge and activation cycles by map-
ping opcode/data among different internal SDRAM banks driven
by the A18–17 pins and external memory selects (

MSx

).

www.BDTIC.com/ADI

«
...
163
164
165
166
167
...
»

Содержание SHARC ADSP-214 Series









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SHARC ADSP-214 Series

Бренд: D-Link Страницы: 15

Бренд: Dahua Страницы: 6

Бренд: Delta Tau Страницы: 74

Extreme Gaming VGA Cooler GV1000

Бренд: ZALMAN Страницы: 7

DL-DVI-Vision-IP Series

Бренд: G&D Страницы: 228

CY62136EV30 MoBL

Бренд: Cypress Semiconductor Страницы: 12

Бренд: Rajant Corporation Страницы: 40

Бренд: Rockwell Automation Страницы: 21

Бренд: Stepper Motor Canada Страницы: 5

Data Capture Board CLC-CAPT-PCASM

Бренд: National Semiconductor Страницы: 15

Бренд: EMC Страницы: 88

Бренд: Lanpro Страницы: 3

Бренд: Lefroy Brooks Страницы: 10

ExpressCard 11-in-1 Reader/Writer

Бренд: SIIG Страницы: 8

Бренд: Mitsubishi Страницы: 188

Бренд: ADC Страницы: 29

Бренд: Cabletron Systems Страницы: 56

IF1-WF 2 Series

Бренд: Citizen Страницы: 45

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды