Analog Devices SHARC ADSP-214 Series Скачать руководство пользователя | Manualshive

Страница: 107 / 1192

background image

ADSP-214xx SHARC Processor Hardware Reference

2-29

I/O Processor

The peripheral’s DMA controller tracks status information of the channels
in each of the peripheral registers (for example

SPMCTLx

,

SPIDMACx

,

DAI_STAT

,

DMACx

, and

MTMCTL

).

• DMA channel status (status bit is set until the DMA terminates)

• TCB chain loading status (status bit is set until TCB loading

completes)

If polling the status of a chained DMA, the DMA status bit is first set
when the TCB has terminated, then it is cleared. The TCB status loading
bit is set until the load is finished and cleared on load completion. This
procedure is repeated for all subsequent DMA blocks.

Note that polling the DMA status registers (especially chained DMA)
reduces I/O bandwidth.

DMA Start and Stop Conditions

The difference between single DMA and chained DMA is based on the
auto-linkage process where the DMA’s attributes are stored in internal
memory and automatically loaded by the IOP if requested.

A DMA sequence starts when one of the following occurs.

• Chaining is disabled, and the DMA enable bit transitions from low

to high.

• Chaining is enabled, DMA is enabled, and the chain pointer regis-

ter address field is written with a non zero value. In this case, TCB
chain loading of the channel parameter registers occurs first.

• Chaining is enabled, the chain pointer register address field is non-

zero, and the current DMA sequence finishes. Again, TCB chain
loading occurs.

www.BDTIC.com/ADI

«
...
105
106
107
108
109
...
»

Содержание SHARC ADSP-214 Series









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SHARC ADSP-214 Series

Бренд: GE Страницы: 93

Бренд: dbx Страницы: 8

Бренд: Data Translation Страницы: 98

Бренд: YASKAWA Страницы: 34

Бренд: Telex Communications Страницы: 28

Бренд: SurfControl Страницы: 2

Бренд: Digi Страницы: 116

DAS-1800HR Series

Бренд: Keithley Страницы: 139

Бренд: Meinberg Страницы: 14

Бренд: A.E.B. Страницы: 28

Бренд: Freescale Semiconductor Страницы: 124

Бренд: Paradyne Страницы: 28

Gen3 Ethernet Module

Бренд: NCD Страницы: 18

Бренд: ZALMAN Страницы: 12

Бренд: Martin Страницы: 41

32R1860 - Nortel Layer 2/3 Copper GbE Switch...

Бренд: IBM Страницы: 14

Бренд: Hanwha Vision Страницы: 131

Бренд: Accusys Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды