Analog Devices SHARC ADSP-214 Series Скачать руководство пользователя | Manualshive

Страница: 881 / 1192

background image

ADSP-214xx SHARC Processor Hardware Reference

A-55

Registers Reference

Control Status Register 0 (SDSTAT0)

The SDRAM control status register provides information on the state of
the SDC. This information can be used to determine when it is safe to
alter SDC control parameters or as a debug aid. This register is shown in

and described in

.

22
(WO)

FMR

Force Load Mode Register Command.

This command performs a

load mode register command immediately.
0 = No effect
1 = Force MR

23

SDBUF

Pipeline Option with External Register Buffer.
0 = No buffer option

1 = External SDRAM CTL/ADDR control buffer enable

26–24

SDTRCD

SDRAM tRCD Specification.

RAS to CAS Delay is = 1–7 SDCLK

cycles. Based on the system clock frequency and the timing specifica-
tions of the SDRAM used. Programmed parameters apply to all four
banks in the external memory.
See the SDRAM data sheet.

29–27

SDRAW

Row Address Width.

000=8, 001=9
010=10, 011=11
100=12, 101=13
110=14, 111=15

30

PGSZ 128

Page Size of 128 Words.

This bit allows programs to configure the

SDC for a page size of 128 words (7 bits) which supports most avail-
able 32 Mb SDRAMs.
0 = No effect, page size decided by SDCAW bits.
1 = Page size 128 words. Column width = 7 bits, override CAW set-
tings.

31

SDAD-
DRMODE

Select Address Mapping.

This bit selects how data is stored in mem-

ory.
0 = Bank interleaving
1 = Page interleaving

Table A-28. SDCTL Register Bit Descriptions (RW) (Cont’d)

Bit

Name

Description

www.BDTIC.com/ADI

«
...
879
880
881
882
883
...
»

Содержание SHARC ADSP-214 Series









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SHARC ADSP-214 Series

Бренд: Cabletron Systems Страницы: 21

Бренд: Garmin Страницы: 2

Бренд: SAF Страницы: 30

IAR KickStart Kit TWR-K60N512-IAR

Бренд: IAR SYSTEMS Страницы: 8

Бренд: Omega Engineering Страницы: 34

DL-DVI-Vision-IP Series

Бренд: G&D Страницы: 228

CY62136EV30 MoBL

Бренд: Cypress Semiconductor Страницы: 12

Бренд: ZALMAN Страницы: 18

OMB-DAQBOARD-500 Series

Бренд: Omega Страницы: 48

Open Standard Module RPX30 EVA-MI V1

Бренд: iesy Страницы: 9

Бренд: WTI Страницы: 178

Бренд: Renesas Страницы: 7

Бренд: Juniper Страницы: 30

Бренд: Paradyne Страницы: 28

Бренд: LevelOne Страницы: 10

Бренд: SET Страницы: 38

StorageWorks TM RAID Array 3000 Pedestal Storage Subsystem

Бренд: Compaq Страницы: 112

ExtremeCloud Appliance E3120

Бренд: Extreme Networks Страницы: 27

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды