Analog Devices SHARC ADSP-214 Series Скачать руководство пользователя | Manualshive

Страница: 583 / 1192

background image

ADSP-214xx SHARC Processor Hardware Reference

13-13

Sony/Philips Digital Interface

In SCDF mode, the transmitter sends successive audio samples of the
same signal across both sub frames, instead of channel A and B. The trans-
mitter will transmit at half the sample rate of the input bit stream. The

DIT_SCDF

bit (bit 4 in the

DITCTL

register selects SCDF mode. When in

SCDF mode, the

DIT_SCDF_LR

bit (bit 5 in the

DITCTL

register) register

decides whether left or right channel data is transmitted.

S/PDIF Receiver

The S/PDIF receiver (

) is compliant with all common serial

digital audio interface standards including IEC-60958, IEC-61937,
AES3, and AES11. These standards define a group of protocols that are
commonly associated with the S/PDIF interface standard defined by
AES3, which was developed and is maintained by the Audio Engineering
Society. The AES3 standard effectively defines the data and status bit
structure of an S/PDIF stream. AES3-compliant data is sometimes
referred to as AES/EBU compliant. This term highlights the adoption of
the AES3 standard by the European Broadcasting Union.

Functional Description



The S/PDIF receiver is enabled at default to receive in two-channel
mode. If the receiver is not used, programs should disable the
receiver as the digital PLL may produce unwanted switching noise.

If the receiver is not used, programs should disable the digital PLL to
avoid unnecessary switching. This is accomplished by writing into the

DIR_RESET

bit in the

DIRCTL

register. In most cases, when the S/PDIF

receiver is used, this register does not need to be changed. After the SRU
programming is complete, write to the

DIRCTL

register with control values.

At this point, the receiver attempts to lock.

For a detailed description of this register, see

“Receive Control Register

(DIRCTL)” on page A-204

.

www.BDTIC.com/ADI

«
...
581
582
583
584
585
...
»

Содержание SHARC ADSP-214 Series









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SHARC ADSP-214 Series

MICROCOMPUTER MN103S

Бренд: Panasonic Страницы: 5

MICROCOMPUTER MN103S

Бренд: Panasonic Страницы: 21

Бренд: Panasonic Страницы: 56

Бренд: Panasonic Страницы: 28

Бренд: Panasonic Страницы: 2

WJMPU955 - PROCESSING UNIT - TMU

Бренд: Panasonic Страницы: 62

ILDA Gem Laser projector tool

Бренд: Stanwax Laser Страницы: 3

EK-FB GA AX370 Gaming RGB Monoblock

Бренд: ekwb Страницы: 2

Бренд: Commell Страницы: 9

Бренд: ZALMAN Страницы: 9

HiGain H2TU-R-402 List 7A

Бренд: ADC Страницы: 7

Бренд: Renesas Страницы: 28

Бренд: Crystal Vision Страницы: 54

Бренд: MEDIATEK Страницы: 166

Бренд: Paradyne Страницы: 6

airMAX NanoBridge M NBM3

Бренд: Ubiquiti Страницы: 24

SmartRack SR25UBEXP

Бренд: Tripp Lite Страницы: 4

AirBridge VS-YOFIMN-000

Бренд: Vivint Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды