Analog Devices SHARC ADSP-214 Series Скачать руководство пользователя | Manualshive

Страница: 453 / 1192

background image

ADSP-214xx SHARC Processor Hardware Reference

9-39

Digital Application/Digital Peripheral Interfaces

latched in one of the

DAI_IMASK_x

registers, all of them must be ser-

viced before executing an RTI instruction.

For more information,

see “Interrupt Controller Registers” on page A-149.

DPI Interrupt Acknowledge

Any asynchronous or synchronous interrupt causes a latency, since it
forces the core to stop processing an instruction in process, then vector to
the interrupt service routine (ISR), (which is basically an interrupt vector
table (IVT) lookup), then proceed to implement the instruction refer-
enced in the IVT.



The DPI triggers one interrupt in the primary IVT.

When a DPI interrupt occurs, the

DPI_IMASK

register determines which of

the 12 interrupt sources requires service.



Reading the DPI’s interrupt latches (

DPI_IMASK

) clears the inter-

rupts (Read-to-Clear bit type). Therefore, the ISR must service

all

the interrupt sources it discovers. That is, if multiple interrupts are
latched in one of the registers, all of them must be serviced before
executing an RTI instruction.

For UART and TWI interrupts in core operation, the interrupt acknowl-
edge mechanisms may be different. For more information, refer to the
specific chapters (

Chapter 20, UART Port Controller

Chapter 21, Two

Wire Interface Controller

Core versus DAI/DPI Interrupts

A pair of registers (

DAI_IRPTL_H

and

DAI_IRPTL_L

) replace functions nor-

mally performed by the

IRPTL

register. A single register (

DAI_IRPTL_PRI

)

specifies to which latch these interrupts are mapped.

Two registers (

DAI_IMASK_RE

and

DAI_MASK_FE

) replace the DAI periph-

eral’s version of the

IMASK

register. As with the

IMASK

register, these DAI

www.BDTIC.com/ADI

«
...
451
452
453
454
455
...
»

Содержание SHARC ADSP-214 Series









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SHARC ADSP-214 Series

Бренд: Paradyne Страницы: 22

Бренд: Sangoma Страницы: 6

Бренд: TC-Helicon Страницы: 2

Бренд: NEC Страницы: 6

Бренд: Vonets Страницы: 8

4 Channel Input Buffer Board SDAIBB

Бренд: B&B Electronics Страницы: 22

Бренд: Quadram Страницы: 21

Бренд: Cypress Semiconductor Страницы: 26

Бренд: Xilinx Страницы: 43

ACC-BKT-AX-BEAM

Бренд: Extreme Networks Страницы: 35

Бренд: C&H Technologies Страницы: 2

Бренд: Thecus Страницы: 148

Бренд: NI Страницы: 8

Бренд: ICP DAS USA Страницы: 8

Бренд: Allied Telesis Страницы: 2

Бренд: Altera Страницы: 43

SteelCentral AppResponse 2170

Бренд: Riverbed Страницы: 166

Бренд: Asus Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды