Analog Devices SHARC ADSP-214 Series Скачать руководство пользователя | Manualshive

Страница: 285 / 1192

background image

ADSP-214xx SHARC Processor Hardware Reference

4-21

Link Ports—ADSP-2146x

LSRs are gated by mask bits and then ORed together to generate the link
service request interrupt. The

LSRQ

interrupt requests may be masked by

the receive (

LRRQ_MSK

) or transmit (

LTRQ_MSK

) bits of the

LCTLx

register.

When the mask bit is set, the interrupt is allowed to pass into the inter-
rupt priority encoder. The maximum latency between asserting the

LCLK

or

LACK

signals and latching an interrupt is 2 to 3

PCLK

cycles.

The interrupt routine must read the

LSTATx

register to determine which

link port to service and whether it is a transmit or receive request. The
link service request status of the port is set whenever the port is not enable
and one of

LxACK

or

LxCLK

is asserted high.

If link service requests are in use, they should be masked out when the
assigned link buffers are being enabled, disabled, or when the link port is
being unassigned in

LCTLx

register. Otherwise, spurious service requests

may be generated.



To avoid the possibility of spurious interrupts, programs can mask
the LSRQ interrupts and poll the appropriate request status bits
until it is cleared and then unmask the interrupt.

Debug Features

The following sections provide information on features that help in
debugging link port software.

Shadow Register

The shadow status register can be read without clearing the interrupt bits.

For more information, see “Link Port Registers” on page A-63.

www.BDTIC.com/ADI

«
...
283
284
285
286
287
...
»

Содержание SHARC ADSP-214 Series









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SHARC ADSP-214 Series

Бренд: Wintech Страницы: 21

Бренд: Glacier Страницы: 2

Compact NVR-AS 4000

Бренд: IndigoVision Страницы: 38

Бренд: ICP DAS USA Страницы: 8

Бренд: Penguin Edge Страницы: 2

Бренд: Renesas Страницы: 4

Бренд: ST Страницы: 67

Бренд: Rane Страницы: 6

Бренд: Adaptec Страницы: 2

Бренд: OWC Страницы: 8

BLUETOOTH RS232RS232

Бренд: Baracoda Страницы: 21

PMP/PTP 450 Series

Бренд: Cambium Networks Страницы: 155

Бренд: LG Innotek Страницы: 14

Бренд: CAME Страницы: 24

Cordio BT4 Radio IP

Бренд: ARM Страницы: 36

Бренд: Crestron Страницы: 40

MEITRACK MVT380

Бренд: Shenzhen Страницы: 8

Бренд: Lava Страницы: 1

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды