Analog Devices SHARC ADSP-214 Series Скачать руководство пользователя | Manualshive

Страница: 1081 / 1192

background image

ADSP-214xx SHARC Processor Hardware Reference

A-255

Registers Reference

Slave Mode Control Register (TWISCTL)

The TWI slave mode control register (

TWISCTL

) shown in

and described in

, controls the logic associated with slave

mode operation. Settings in this register do not affect master mode opera-
tion and should not be modified to control master mode functionality.

Figure A-145. TWISCTL Register

Table A-138. TWISCTL Register Bit Descriptions (RW)

Bit

Name Description

0 TWISEN

Slave Enable.

0 = The slave is not enabled. No attempt is made to identify a
valid address. If cleared during a valid transfer, clock stretching
ceases, the serial data line is released and the current byte is not
acknowledged.
1 = The slave is enabled. Enabling slave and master modes of
operation concurrently is allowed.

1

TWISLEN

Slave Address Length.

0 = Address is a 7-bit address
1 = Reserved. Setting this bit to 1 causes unpredictable behavior.

2

TWIDVAL

Slave Transmit Data Valid.

0 = Data in the transmit FIFO is for master mode transmits and is
not allowed to be used during a slave transmit, and the transmit
FIFO is treated as if it is empty.
1 = Data in the transmit FIFO is available for a slave transmission.

TWI

S

EN

TWIDVAL

TWINAK

TWIGCE

TWI

S

LEN

S

lave Ena

b

le

S

lave Address Length

S

lave Transmit Data Valid

Not Acknowledge

General Call Ena

b

le

0

9

8

3

7

5

6

4

2

1

14

12

11 10

1

3

15

www.BDTIC.com/ADI

«
...
1079
1080
1081
1082
1083
...
»

Содержание SHARC ADSP-214 Series









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SHARC ADSP-214 Series

Бренд: Farallon Страницы: 26

Бренд: Observint Страницы: 11

Бренд: Xinje Страницы: 57

Z3-DM8168-PCI-RPS

Бренд: Z3 Technology Страницы: 20

Z3-DM8107-SDI2-RPS

Бренд: Z3 Technology Страницы: 75

Бренд: Z-Wave Страницы: 13

Бренд: Teac Страницы: 20

cMT-FHDX Series

Бренд: Maple Systems Страницы: 2

Бренд: NETGEAR Страницы: 2

Бренд: Garland Страницы: 43

Oresund EFC102200

Бренд: Bridgeworks Страницы: 84

Бренд: WABCO Страницы: 29

Бренд: ICP DAS USA Страницы: 8

Бренд: Penguin Edge Страницы: 2

Бренд: H3C Страницы: 34

Бренд: FOR-A Страницы: 37

PD-9501-10GCO/AC

Бренд: Microchip Technology Страницы: 41

Бренд: Jetter Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды