Analog Devices SHARC ADSP-214 Series Скачать руководство пользователя | Manualshive

Страница: 876 / 1192

background image

ADSP-2147x, ADSP-2148x External Port Registers

A-50

ADSP-214xx SHARC Processor Hardware Reference

16–14

IC

Bus Idle Cycle.

Default Idle cycles are inserted whenever read to

write in a bank or read to read between two external banks or a read
to the SDC happened.
000 = 0 cycles, 001 = 1 cycle
010 = 2 cycles, 011 = 3 cycles
100 = 4 cycles, 101 = 5 cycles
110 = 6 cycles, 111 = 7 cycles
A bus idle cycle is an inactive bus cycle that the processor automati-
cally generates to avoid data bus driver conflicts. Such a conflict can
occur when a device with a long output disable time continues to
drive after

RD

is deasserted, while another device begins driving on

the following cycle. Idle cycles are also required to provide time for
a slave in one bank to three-state its ACK driver, before the slave in
the next bank enables its ACK driver.

17 (WO)

AMIFLSH

AMI Buffer Flush.

Flushes both AMIRX and AMITX buffers.

0 = Buffer holds the data
1 = Flush the buffer

20–18

RHC

Read Hold Cycle.

Controls the delay between two reads.

000 = Disable read hold cycle
001 = Hold address for one cycle
010 = Hold address for two cycles
A read hold cycle is the delay between two reads at the end of a read
access. Programs may disable the read hold cycle, or hold the
address for one or more external port clock cycles.

21

PREDIS

Disable Predictive Reads.

Default is predictive reads are enabled.

Note this bit is global, if set it does apply to all external banks.

31–22

Reserved

Table A-26. AMICTLx Register Bit Descriptions (RW) (Cont’d)

Bit

Name

Description

www.BDTIC.com/ADI

«
...
874
875
876
877
878
...
»

Содержание SHARC ADSP-214 Series









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SHARC ADSP-214 Series

Бренд: National Instruments Страницы: 85

SmartMedia Adapter PC Card REX-SMA01F

Бренд: Ratoc Systems Страницы: 75

Бренд: Commell Страницы: 58

Бренд: Xilica Audio Design Страницы: 30

Бренд: MFJ Страницы: 11

Бренд: ZoneVu Страницы: 15

Бренд: FUNcube Страницы: 23

Бренд: Raven Страницы: 33

Бренд: Fast Страницы: 66

FiberTwist XGS2410

Бренд: Genexis Страницы: 7

METERS AND MORE UM2241

Бренд: ST Страницы: 26

Бренд: Grundfos Страницы: 40

Бренд: Idis Страницы: 40

Бренд: Paradyne Страницы: 46

Threat Analysis Reporter TAR

Бренд: 8e6 Technologies Страницы: 76

PC/104-PCMCIA-1

Бренд: Kontron Страницы: 20

GPX-N 1080Ti-M23

Бренд: Alphacool Страницы: 4

Бренд: Crown Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды