
!
DANGER
BODY ENTANGLEMENT
HAZARD
ROTATING DRIVELINE
To prevent severe injury or
death:
•
Avoid all contact with PTO
shaft while shaft is in motion.
80949
Attaching and Checking
Driveline
IMPORTANT!
Your AMADAS M2120A has
been equipped with a constant velocity PTO
driveline. Because of the double Cardan Joint
incorporated into this shaft, you can expect
a constant output shaft speed with minimal
vibration. The shaft speed will remain constant
with minimum vibration even in a tight turning
radius.
Please read the section on lubrication in
Chapter 7.
Maintenance
thoroughly. The PTO
drive shaft has special requirements.
Death or serious personal injury will
result from entanglement.
ALWAYS make sure all drive shields and
guards are in place when the combine is in
operation.
1. REMOVE
the tractor key and keep in possession
while working on, under, and around the tractor.
2. Make sure the tractor draw bar is set with the
center of the hitch approximately 3-1/2” below the
centerline of the tractor PTO output shaft.
3. Extend the tractor draw bar until the center of the pin
hitch is approximately 20” from the end of the tractor
PTO output shaft. Refer to Figure 3-5.
4. If your combine is equipped with a pin type hitch,
use the same 20” dimension to center the tractor
clevis pin.
20”
16”
5”
PTO Between 5” and
16” above drawbar
Figure 3-6: PTO Driveline Placement Measurements
5. If equipped with a side shift tongue, shift the
tongue to the operating position (left side).
6. Attach the driveline to the combine and tractor PTO.
Note:
1-3/8” 21 spline and 1-3/4” 20 spline
ends are available.
Figure 3-7: PTO Driveline
Driveline Combine
Side
CV Joint
U-Joint &
Shield
Shield
Driveline
Tractor
Side
Note:
A tractor draw bar extension (AMADAS
part #61359) may be required to attain a distance
of 20” between the tractor PTO output and the
hitch ball on tractors with 1-3/8” 21 spline PTO.
!
DANGER
ALWAYS stop the combine, set the
parking brake, shut the tractor motor off,
and remove the key before you leave the
tractor for any reason.
!
DANGER
Operation
M2120A PT Peanut Combine
4/26/19
MAN152
34
Содержание M2120A
