Yamaha RCX142 User Manual Download Page 63

Page: 63 / 450

Operation

1. Operation overview

The controller configuration and main functions are shown below.

Set up the equipment as needed according to the operation to be performed.

Fig. 4-1-1 Operation overview

Parallel I/O interface

Robot

Power input

External

circuit

AC power input terminal

Programming box MPB

SAFETY I/O interface

• Used to supply power to the controller.

MPB is used for
• robot operation
• programming
• teaching
• parameter input, etc.

• Used for basic input/output operations.

• Used for input/output of emergency stop

signal, enable switch signal, etc.

• Used for communication through
RS-232C.

RS-232C interface

Controller

This chapter mainly explains how to operate the MPB programming box.

NOTE

• Refer to Chapter 6 for Parallel I/O

interface.

• Refer to Chapter 7 for SAFETY

I/O interface.

• Refer to Chapter 8 for RS-232C

interface.

CAUTION

The external circuit connected to the
robot controller should be prepared
by the user.

Summary of Contents for RCX142



































































































































































































































































































































































































































































Search results

Summary of Contents for RCX142

Reviews:

Related manuals for RCX142

Brands by name

Popular brands

Yamaha RCX142, User Manual

Search results

Summary of Contents for RCX142

Reviews:

Related manuals for RCX142

Brands by name

Popular brands