VeEX VePAL TX300M User Manual Download Page 36

Page: 36 / 421

Out of Service:

Should be selected if the incoming signal is expected to contain a known test pattern. Deselect this option if

signal is expected to contain live network traffic – this will disable the pattern detection process and will enable the reporting of

LSS.

PRBS Pattern:

Same options as Transmitter described previously.

Invert:

Same options as Transmitter described previously.

Go back to top

Go back to TOC

TX300S_e-manual_D07-00-064P_RevA00

Summary of Contents for VePAL TX300M






































































































































































































































































































































































































































Search results

Summary of Contents for VePAL TX300M

Reviews:

Related manuals for VePAL TX300M

Brands by name

Popular brands

VeEX VePAL TX300M, User Manual

Search results

Summary of Contents for VePAL TX300M

Reviews:

Related manuals for VePAL TX300M

Brands by name

Popular brands