VeEX VePAL TX300M User Manual Download Page 331

Page: 331 / 421

Note

: To run the test, make sure that traffic is being looped back at the far-end of the network under test.

Configuration Test

The

Config. Tests

tab lists the Pass/Fail status of each service and test. Tapping on the table brings up a screen with

CIR

CIR/EIR

and

Policing Test

results for the chosen Service.

CIR

CIR/EIR Test

, and

Policing

tabs display min, mean, and max

values for

IR Mbps

FTD

FDV

Frame Loss Count

, and

Frame Loss Ratio (%).

If Step Load was selected for the CIR Test,

these values will be displayed for each step. If any measured values do not meet the service test parameters set in the

Bandwidth and Threshold tabs, the test fails.

IR Mbps:

Information Rate. Measures the average Ethernet frame rate starting at the MAC address field and ending at the

CRC.

FTD:

Measures the time that the frames can take to travel from source to destination.

FDV:

Measures the frame jitter.

Frame Loss Count:

Counts the number of lost frames.

Frame Loss Ratio:

Ratio of lost frames to the total transmitted frames.

CIR Test - Service 1

CIR test

: The test passes if all measured values are below the thresholds configured. If a threshold is disabled, it will not be

TX300S_e-manual_D07-00-064P_RevA00

Summary of Contents for VePAL TX300M






































































































































































































































































































































































































































Search results

Summary of Contents for VePAL TX300M

Reviews:

Related manuals for VePAL TX300M

Brands by name

Popular brands

VeEX VePAL TX300M, User Manual

Search results

Summary of Contents for VePAL TX300M

Reviews:

Related manuals for VePAL TX300M

Brands by name

Popular brands