VeEX VePAL TX300M User Manual Download Page 156

Page: 156 / 421

0001 Stratum 1

0100 Transit Node Clock

0111 Stratum 2

1010 Stratum 3

1100 SDH Minimum Clock

1101 Stratum 3e

1110 Previsional by the Network Operator

1111 Not used for synchronization

Other bytes are reserved

S1 Byte (Synchronization Status)

Order Wire Byte (E2)

A 64kbps voice communication channel between multiplexers.

It’s a channel used by craft persons and will be ignored as it passes through regenerators.

The relief byte is used for ring protection

Go back to top

Go back to TOC

Path Overhead Layer

The following is a partial list of POH bytes and their corresponding functions:

J1 byte (STS Path Trace)

High Order VC-N path trace byte

A unique message is assigned to each path in a SDH network – therefore the path trace can be used to check

continuity between any location on a transmission path and the path source

This user programmable byte repeatedly transmits a 15-byte string plus 1 (CRC-7) byte so that a receiver can

continually verify its connection with the transmitter

A 64-byte free-format string is also permitted

The message is transmitted one byte per VC-4 frame

J1 Byte (HP Path Trace)

TX300S_e-manual_D07-00-064P_RevA00

Summary of Contents for VePAL TX300M






































































































































































































































































































































































































































Search results

Summary of Contents for VePAL TX300M

Reviews:

Related manuals for VePAL TX300M

Brands by name

Popular brands

VeEX VePAL TX300M, User Manual

Search results

Summary of Contents for VePAL TX300M

Reviews:

Related manuals for VePAL TX300M

Brands by name

Popular brands