VeEX VePAL TX300M User Manual Download Page 349

Page: 349 / 421

Rates:

Rate information associated with each stream.

Throughput Results - Summary per Stream

Go back to top

Go back to TOC

The

Per Stream Errors

screen displays the Current and Total error count of each stream.

Bit:

Indicates errors related to test pattern (Bit Error or LSS [Pattern Loss])

BER:

Bit Error Ratio

FCS/CRC:

Number of received frames with an invalid Frame Check Sequence (FCS)

IP Checksum:

Invalid IP Frame Check sequence

TCP/UDP Checksum

(Layer 4 only)

Jabber frames:

Number of received frames larger than 1518 bytes containing an invalid FCS

Runt frames:

Number of received frames smaller than 64 bytes containing an invalid FCS

Frame Loss
Frame Loss %
OOS

Throughput Results - Errors per Stream

Throughput Results - Errors per Stream (page 2)

TX300S_e-manual_D07-00-064P_RevA00

Summary of Contents for VePAL TX300M






































































































































































































































































































































































































































Search results

Summary of Contents for VePAL TX300M

Reviews:

Related manuals for VePAL TX300M

Brands by name

Popular brands

VeEX VePAL TX300M, User Manual

Search results

Summary of Contents for VePAL TX300M

Reviews:

Related manuals for VePAL TX300M

Brands by name

Popular brands