VeEX VePAL TX300M User Manual Download Page 152

Page: 152 / 421

Path Trace Byte (J0)

Regenerator section trace

Used to transmit a 16 or 64-byte identifier (trace) (including a CRC-7 byte) repeatedly so that all regenerators can verify

their connection

Used for continuity testing between regenerators

B1 Byte (RS-BIP)

An 8-bit even parity code used to check for transmission errors over the regenerator section

Its value is calculated over all the bits of the STM-1 frame before scrambling

The checksum value is placed in the RS overhead of the following STM-1 before scrambling

Path Trace Byte (J0)

Order Wire Byte (E1)

Local order wire channel for voice communication between regenerators, cross connects, hubs and remote terminal

locations

F1 Byte

Section user channel

TX300S_e-manual_D07-00-064P_RevA00

Summary of Contents for VePAL TX300M






































































































































































































































































































































































































































Search results

Summary of Contents for VePAL TX300M

Reviews:

Related manuals for VePAL TX300M

Brands by name

Popular brands

VeEX VePAL TX300M, User Manual

Search results

Summary of Contents for VePAL TX300M

Reviews:

Related manuals for VePAL TX300M

Brands by name

Popular brands