VeEX VePAL TX300M User Manual Download Page 213

Page: 213 / 421

APS Test Procedure:

The TX300/e should be connected to a transmission system to ensure that the switching time is measured for the service

transported by the E1 links

Ensure that no errors or alarms are present on the transmission system because this will impact the measurement

The measurement will be triggered by an Alarm Indication Signal (AIS)

The TX300/e measures how long the AIS event remains present after the event is first recognized and will continue to

measure the total disruption time in the event of multiple disruptions

E1 APS

Go back to top

Go back to TOC

11.4 E1 Frame Words

This function requires the E1 signal to be framed. The NFAS word is used to carry information about the status of the link and to

provide control signals for primary rate multiplexers.

Bit 1: Reserved for International use (M is used to transmit the CRC multiframe signal in PCM30C and PCM31C)

Bit 2: Set to “1” to prevent simulation of FAS

Bit 3: "A" shows the remote alarm indication

Bits 4 to 8: Sa4 to Sa8 are spare bits

TX:

Bits Sa4 to Sa8 are used to send optional network messages. The Sa bits should be set to “1” when they are not used or

when links cross International borders.

RX:

Bit Sa4 can be used as a message based data link for operations, maintenance and performance monitoring.

E1 Framed RX

TX300S_e-manual_D07-00-064P_RevA00

Summary of Contents for VePAL TX300M






































































































































































































































































































































































































































Search results

Summary of Contents for VePAL TX300M

Reviews:

Related manuals for VePAL TX300M

Brands by name

Popular brands

VeEX VePAL TX300M, User Manual

Search results

Summary of Contents for VePAL TX300M

Reviews:

Related manuals for VePAL TX300M

Brands by name

Popular brands