VeEX VePAL TX300M User Manual Download Page 404

Page: 404 / 421

17.0 CPRI Testing

Overview

Interface Specifications

CPRI Testing

QoS Requirements
Test Areas
Test Ports

CPRI BERT Setup

Test Pattern
Traffic Pattern
Error Injection

CPRI BERT Results

Summary
Signal
Errors
Alarms
Events

Saving and Retrieving Files
File Management in ReVeal

CPRI Overview

CPRI stands for

Common Public Radio Interface

This protocol has been developed by Ericsson AB, Huawei Technologies Co. Ltd, NEC Corporation, Alcatel Lucent and Nokia

Siemens

It is an industry cooperation aimed at defining a publicly available specification for the key internal interface of radio base

stations between the Radio Equipment Control (REC) and the Radio Equipment (RE)

The standard is public and can be downloaded from

http://www.cpri.info

The current version is v4.2 (2010-09-29)

Go back to top

Go back to TOC

17.1 Interface Specifications

CPRI specification defines only Layer 1 and Layer 2

Specification written with the goal to be generic enough to support scalable rates, physical access medium type, and air

interface technologies

Go back to top

Go back to TOC

TX300S_e-manual_D07-00-064P_RevA00

Summary of Contents for VePAL TX300M






































































































































































































































































































































































































































Search results

Summary of Contents for VePAL TX300M

Reviews:

Related manuals for VePAL TX300M

Brands by name

Popular brands

VeEX VePAL TX300M, User Manual

Search results

Summary of Contents for VePAL TX300M

Reviews:

Related manuals for VePAL TX300M

Brands by name

Popular brands