VeEX VePAL TX300M User Manual Download Page 185

Page: 185 / 421

Path Trace Byte (J0)

Regenerator section trace

Used to transmit a 16 or 64-byte identifier (trace) (including a CRC-7 byte) repeatedly so that all regenerators can verify

their connection

Used for continuity testing between regenerators

B1 Byte (RS-BIP)

An 8-bit even parity code used to check for transmission errors over the regenerator section.

Its value is calculated over all the bits of the STS-N frame before scrambling

The checksum value is placed in the SECTION overhead of the following STS-N before scrambling

B1 (Section-BIP) Byte

Order Wire Byte (E1)

Local order wire channel for voice communication between regenerators, cross connects, hubs and remote terminal

locations

F1 Byte

Section user channel

TX300S_e-manual_D07-00-064P_RevA00

Summary of Contents for VePAL TX300M






































































































































































































































































































































































































































Search results

Summary of Contents for VePAL TX300M

Reviews:

Related manuals for VePAL TX300M

Brands by name

Popular brands

VeEX VePAL TX300M, User Manual

Search results

Summary of Contents for VePAL TX300M

Reviews:

Related manuals for VePAL TX300M

Brands by name

Popular brands