VeEX VePAL TX300M User Manual Download Page 33

Page: 33 / 421

Tx Pattern Setup

Pattern:

Use the pattern drop-down box to select the test pattern which will be inserted into the transmitted signal. Pseudo

Random Bit Sequences (PRBS) defined by ITU-T 0.150 and 0.151 standards, fixed words and 24-bit or 32 bit user defined

patterns are available. Note, if the 32 bit user pattern entered is incorrect, the default pattern will be 0xFFFFFFFF.

Invert:

Inversion of polarity is also available.

Note:

ITU-T specification 0.150 recommends the following test patterns:

Go back to top

Go back to TOC

6.2.2 Receiver Setup

Hierarchy

Tapping the Hierarchy box opens the Rx Hierarchy Setup screen.

Rx Hierarchy Setup

TX300S_e-manual_D07-00-064P_RevA00

Summary of Contents for VePAL TX300M






































































































































































































































































































































































































































Search results

Summary of Contents for VePAL TX300M

Reviews:

Related manuals for VePAL TX300M

Brands by name

Popular brands

VeEX VePAL TX300M, User Manual

Search results

Summary of Contents for VePAL TX300M

Reviews:

Related manuals for VePAL TX300M

Brands by name

Popular brands